Lower Guitar Bridge

Br E E D Love O W N E R’s M A Nu A L
The bridge truss in your Breedlove guitar is adjusted before leaving the factory, and should require very little attention from that point on. However, the system should be checked periodically for proper adjustment. Cutaway of a Breedlove guitar, showing JLD bridge truss Nylon string guitars, Revival, and Passport Series instruments do not have a ... View This Document

Care & Maintenance - Larrivée
Slightly collapsed (concave), action may lower slightly, bridge wings will appear concave, the guitar may develop a buzz. Fret Ends will feel sharp, Soundboard and back will become flat or collapsed (concave), action will feel lower, guitar will likely buzz, Bridge wings will appear concave, after several months the bridge may “lift” or ... Access Doc

GIBSON GUITAR CORP. PRODUCT AND CARE GUIDE
1. At the Bridge The lower end of an acoustic instrument is strung as shown on the left of the page. Different instruments are strung according to the bridge and string type. The bridge end is always strung beforethe string posts at the head-stock. 2. At the Headstock To fasten a string on the post and prevent slipping, bring the ... Read Content

Taylor Guitars Production Set-Up Specifications
With the top surface of the bridge. DN/GO 6-str. – top surface of the bridge.set angle slightly below bridge surface to achieve higher action spec. Sight as on steel-string but the level fret plane should be aligned to a point 1/3 of bridge thickness below the top surface. Top of level fret plane pointed slightly (.010-.015”) above the ... Fetch Document

Ovation Guitars Are Played By Countless Musicians Around The ...
Transporting your Ovation guitar that will minimize the chances of damage. When transporting in a car, always keep the case Bridge Bowl (Back and Sides) Sound board (Top) Purfling 4 5. The Ovation Family of Guitars. Ovation builds a wide range of products appropriate for . ... Access Full Source

RESOMAX™ BRIDGE INSTALLATION INSTRUCTIONS 1 2
Bridge posts. Raise or lower the treble and bass sides of the bridge until correct string height (measured in Step 1) is acheived. Tune the guitar to concert pitch after the adjustment and check the string height at the 12th fret. If the strings touch the bridge body behind the saddles, raise the tail piece until the ... Fetch Document

The Taylor SolidBody - Guitars
Accessible from the back of the guitar and sandwiches the guitar body between the plate and the bezel. Action Adjustment Quick Tips • Two anchor nuts (Fig 2) hold the bridge assembly together. Do not remove them or the bridge will come off. • Three action height adjustment screws (Fig 3) are used to lower and raise the action. ... Read Content

Machine Head - Wikipedia
A machine head (also referred to as a tuning machine, tuner, or gear head) is a geared apparatus for tuning stringed musical instruments by adjusting string tension. Machine heads are used on mandolins, guitars, double basses, and others, and are usually located on the instrument's headstock . ... Read Article

Starcaster By Fender - Wikipedia
Starcaster by Fender is a range of instruments and accessories aimed at students/beginners, marketed by the prominent guitar company Fender from the early 2000s until at least 2011. As of April 2018 no products were being marketed under this brand. ... Read Article

Guitars. In fact, there are only a few values that you’re likely to see in any guitar – 250 k, 500 k, 1 Meg, and 2 Meg on occasion. If your guitar bridge humbucker seems “too bright,” and you have 500 k volume and tone pots, try dropping the value of the volume pot to 250 k to reduce the amount high frequencies in the signal. The lower ... View Full Source

Relocating A Tune-O-Matic bridge - YouTube
This bridge is in the wrong spot, so the guitar can’t play in tune. Rather than drill new holes in a vintage guitar body, Dan Erlewine comes up with a clever solution. For more information on ... View Video

Duesenberg Guitars - Wikipedia
Set mahogany neck and flat top mahogany body. The guitar is equipped with a wrap-around tailpiece and a single Domino P90 pickup in a special 3-point dog-ear nickel-silver housing in bridge position, which is controlled by a 3-way switch. Despite the guitar having only one pickup, the special wiring allows for three different types of sound. ... Read Article

The Innovators Of High Performance Guitar Components ...
The Innovators of High Performance Guitar Components & Accessories. Table of conTenTs equipped to handle custom requests quickly, efficiently, and at a lot lower cost than “I just replaced the bridge pins on my Blueridge guitar with TUSQ pins. What a difference! ... Read More

FX FIXED BRIDGE XS TREMOLO BRIDGE INSTRUCTION SHEET
Adjust the bridge so there is no tremolo movement required to engage the lock: 1. Using the large thumbscrew under the bridge, tighten or loosen the tremolo spring tension to align the notch to the tab. 2. Turn the thumbscrew another 50% more, so the tab is on the opposite side of the notch from where it started. 3. Re-tune the guitar. 4. ... Read Full Source

OWNER’S MANUAL & WARRANTY INFORMATION
Cleaning your guitar regularly is one of the best ways to maintain the finish and prolong string life. Clean your guitar after each use, making sure to wipe the fingerboard and strings as well as any of the plated parts such as tuners, pickups, bridge etc. Make sure to remove all perspiration, as it can lead to corrosion ... View Document

ELECTRIC GUITAR - Yamaha Downloads
The bridge back to the parallel position. The adjustment procedures are: 1) Remove the screws that attach the tremolo cavity back plate from the back side of the guitar exposing the claw springs. 2) Make sure that the guitar is tuned to proper pitch. 3) If the bridge is tilted forward (up), tighten spring tension ... Fetch Document

Guitar The 5 Adjustments Rez-o-tube Guide System 6
Is fitted within the bridge to capture the maximum resonance. 6 7Adjusting the Rez-o-tube® floating bass bridge The floating bass bridge angle can be adjusted by removing the back plate and turning the two screws to tighten or slacken the two tension springs. When your bass guitar is tuned to concert pitch the bridge angle ... Retrieve Document

Parker PDF Series Manual
Adjustments for string height are made from the front of the guitar, on the bridge located behind the pick-ups. Intonation adjustments are also made via the bridge on the front side of the guitar. A. Bass side height adjustment screw - turn clockwise to lower this part of the bridge, turn counter clockwise raise this part of the bridge. ... Get Doc

2018: The Year The 1975 Spoke For A Generation
The band's entire label team at Dirty Hit, a record company run jointly with Healy, was working around the clock without sleep. Whether it was ... Read News

Guitar Bridges - Ibanez Japan
Guitar Bridges To change strings, thread the new strings through the string grommets located on the back of the guitar and bring them up and over the saddle. The intonation can be adjusted by adjusting the saddle forward or backward using a Phillips (+) head screwdriver on the intonation adjustment screw at the rear of the bridge. ... Read Full Source

Adjusting A guitar Tremolo System - YouTube
Www.maxedoutguitar.com Adjusting the height of your bridge is much easier than beginners think it is. It only requires a screwdriver and about 3-4 minutes to complete. ... View Video

The Parts Of A Guitar - Magnolia Guitar Lessons & Repairs ...
Body of the guitar Bridge Pins: Saddle: part of the bridge & the lower contact point for the strings; in acoustic guitars it is generally 1 or 2 pieces; in electric guitars there may be several individually adjustable pieces The Parts of a Guitar. ... Fetch Here